I’ve been in Puerto Williams, Chile, working on Morgane for just over two weeks now and apologise for not getting an entry online earlier but I have been working long hours to get things done. I sailed over here, from Stanley, with my friend Brice on his yacht ‘Podorange’ an ex BT challenge 67 yacht that he now charters down here in the SW Atlantic and Antarctica.
On arrival I unloaded the new sails that I had brought Quantum in Cape Town, South Africa, and all the boxes of odds and ends that had been sent to Stanley for me and got to work. The first think I had to tackle was to clean up the galley and one of the bunks as everything was rather damp and smelly after the boat has been sitting for so long. I got the shore power connected and got an electric fan heater to work to help air the boat out.
The first job, other than the clean up which is ongoing, was to hook up the batteries and get the shore-power battery charger working. That gave me light to work with in the evenings. Another day was spent on fitting the new sails and pulling in the new running rigging; all seems ok but the ultimate trial won’t come for a little while yet when I get out to test them.
I got fed up moving the box containing the new wind generator every time that it got in the way so mounted that and got it working. It only really works when the wind is in the south west here as we are so sheltered but at least yesterday I had a day of free power.
I had to remove the old wood burner and chimney (see the photo below) as it was in the way of all the following projects. I was expecting to find a horrible rusty hole in the coach roof when I pulled out the old chimney but instead found good clean solid steel. I fitted the through deck fitting for the new chimney so that the deck was weatherproof and so that the sealant would have time to cure while I messed around with things electrical.
I then got into a several day project which was to build a new 12 Volt power distribution panel and instrument panel alongside the existing chart table. All of this a temporary installation until such time as I get to some place where I will refit the interior of the yacht.
Here is photo of the old electrical panel which was a mishmash of several different type of breakers, switches, wire, fuses etc.. The big tube up the right side of the picture is the chimney from the big wood burning space heater; which is no longer there – more on that later.
I got hold of some fairly decent ply from a packing case that I was given and made a plan to cover the front of the shelves that you see in the photo and mount the new electrical panels and instruments on the ply. I had two 12 Volt distribution panels and a battery monitor to mount on one side and a couple of instruments and the HF and vhf radios to mount on the other.
I laid everything out and decided that it would all fit and fired up the jigsaw to cut out the mounting holes.
The right panel holds the battery status monitor and two 12 Volt DC breaker panels. One of those has two cigar lighter type outlets (handy for charging iPods and camera batteries).
The left panel is instruments and radios. From top left, clockwise, we have an electronic recording barometer, an aneroid barometer, AIS transponder and display, the Pactor modem for receiving weather fax and email over the HF radio, on the bottom we have the VHF radio, above that the HF radio, and a multi-function instrument display from Furuno.
The Furuno multi-function display (an RD-33) is connected to a NMEA 2000 network which connects to the wind instrument, gps, depth, speed, compass etc..
Above the laptop screen you can see an old but good Furuno GPS navigator that I’ll keep.
The laptop is running MaxSea’s TimeZero charting and navigation software and also connected to the NMEA 2000 (N2K) network via an interface that produces a USB output. The AIS transponder is networked with the radio and the computer giving the ability to directly call approaching ships by selecting them on the AIS screen. Any DSC calls received should show up on the screens too.
Enough technical chat and on with the work! The next thing I tackled was to relocate the fuse and breaker for the anchor windlass which would otherwise have been difficult to reach behind the heater which I planned to install next.
A big milestone was getting the new Refleks diesel heater installed which was more or less a two day job, three including installing the through-deck fitting mentioned earlier. The day I lit the heater the outside temperature was just a couple of degrees with sleet and lots of wind so a great day to test the heater! It’s been in use for a few days now and I am learning where to set the control knob to achieve the desired cabin temperature.
Today I moved onto putting the engine back into service. Apart from a full service I have a new smart alternator/battery charger to install and have to replace the Morse controller (the combined throttle and gear change lever that is located in the cockpit).
But, before I wanted to work on the engine it needed a massive clean up, and that little job took all of today. You can see the results in the photo on the right. I consider today’s clean up a first pass; it’ll take another day when I have the time to be more concerned with cosmetics.
Still lots to do but that is progress so far. It’s late and I’m tired so apologies for the bad grammar and spelling mistakes!